Multi-mount Cylinder、Twin-rod Cylinder、Tri-rod Cylinder
AirTAC TCM Series Tri-Rod Aluminum Alloy Pneumatic Air Cylinder TCM32X70S TCM32X75S TCM32X80S TCM32X90S TCM32X100S
  • 2-2
  • 1-2
  • 3-2
  • 4-2
  • 5-2
  • 6-1
AirTAC TCM Series Tri-Rod Aluminum Alloy Pneumatic Air Cylinder TCM32X70S TCM32X75S TCM32X80S TCM32X90S TCM32X100S

Product Name: TCM Series Tri-rod Cyclinder
Product Model: TCM32X70S TCM32X75S TCM32X80S TCM32X90S TCM32X100S
Valve Type: Tri-rod Cyclinder, Cyclinder
Brand: AirTAC
Fluid: Air
Acting Type: Double Acting



Bore size: 12 16 20 25 32 40 50 63
Acting type: Double Acting
Air(to be filtered by 40μm filter element)
Operating Pressure: 0.1~1.0MPa(15~145psi)
Proof pressure: 1.5MPa(215psi)
Temperature(℃): -20~70
Speed rang (mm/s): 30~500 
Stroke tolerance: (0~+1.0) 
Cushion Type: Burmper
Non-rotating Tolerance: ±0.08° ±0.07° ±0.06° ±0.05°
±0.10° ±0.09° ±0.08° ±0.06°
Port Size: M5X0.8
PT1/8 PT1/4

①Non-rotary accuracy of the cylinder fully retracted state, the cylinder fixed plate can be rotated angle;
②PT thread, NPT thread and G thread are available.


Bore size(mm) Standard Stroke(mm) Max Stroke(mm)

10 20 25 30 40 50 60 70 75 80 90 100 125 150 150
16 10 20 25 30 40 50 60 70 75 80 90 100 125 150 175 200 200
20/25 20 25 30 40 50 60 70 75 80 90 100 125 150 175 200 225 250 250
32/40/50/63 25 30 40 50 60 70 75 80 90 100 125 150 175 200 225 250 250

① Different from the standard stroke 1 ~ 5mm non-standard stroke cylinder, cylinder from the previous standard stroke restructuring, the same size and shape.

Such as the trip for the 86 non-standard stroke cylinder is a standard stroke of 90 standard cylinder restructuring, its dimensions and the same;

However, the non-standard stroke cylinder with a stroke of 84 differs from the standard stroke 90 of the previous stage by 6mm, and can only be ordered in non-standard form.

Product Feature:

1. JIS standard is implemented.

2. Two guides of special bearing steel and linear bearing or bronze bearing guide are used to prevent rotating. They can bear high torque and radial load.

    ★Note: Steel ball linear bearing: It is suitable for elevation action of cylinder or the situation requiring high precision and high bearing ability, especially for the situation requiring low fraction action process.

      Bronze sliding bearing: it is suitable for the action that has radial load resistance. Compared with normal cylinder of same use, the horizontal impact resistance is doubled and it has stronger torsion rigidity.

3. Drive unit and guide unit are in the same barrel that no additional accessories are needed with minimal space required. The air intake is optional and it is convenient to install.

4. The bottom, back side and fixing plate of main body respectively has two exact orientation orifices (See ΦPA orifice and the orifice in XX point), which can provide orientation installation with high precision for the special situation.

5. Options of switch mounting with provision 4 mounting slots.

6. Special design of main body provides multi-mount;

Installation & Usage:

1.When load changes in the work, the cylinder with abundant output capacity shall be ed.

2.Relative cylinder with high temperature resistance or corrosion resistance shall be chosen under the condition of high temperature or corrosion.

3.Necessary protection measure shall be taken in the environment with higher humidity, much dust or water drops, oil dust and welding dregs.

4.Dirty substances in the pipe must be eliminated before cylinder is connected with pipeline to prevent the entrance of particles into the cylinder.

5.The medium used by cylinder shall be filtered to 40μm or below.

6.Anti-freezing measure shall be adopted under low temperature environment to prevent moisture freezing.

7.The cylinder shall be carried out test run without load before application. Prior to run, buffer shall be turned to the minimum and gradually released to avoid the damage on cylinder caused by excessive impact.

8.The cylinder shall avoid the influence of side load in operation to maintain the normal work of cylinder and extend the service life.

9.If the cylinder is dismantled and stored for a long time, please conduct anti-rust treatment to the  surface. Anti-dust caps shall be added in air inlet and outlet ports.

Order Code:
TCM Series.jpg

TCL Series.jpg

TCM20X20-S TCM16X100S TCM32X100S TCM63X50S TCM80X200S
TCM6X5S TCM16X150S TCM32X150S TCM63X75S TCM80X225S
TCM6X10S TCM20X25S TCM32X200S TCM63X100S TCM80X250S
TCM6X15S TCM20X50S TCM32X250S TCM63X150S TCM100X25S
TCM6X20S TCM20X75S TCM40X25S TCM63X200S TCM100X30S
TCM10X5S TCM20X100S TCM40X50S TCM63X250S TCM100X40S
TCM10X10S TCM20X150S TCM40X75S TCM80X25S TCM100X50S
TCM10X15S TCM20X200S TCM40X100S TCM80X30S TCM100X60S
TCM10X20S TCM20X250S TCM40X150S TCM80X40S TCM100X70S
TCM10X25S TCM25X25S TCM40X200S TCM80X50S TCM100X75S
TCM10X30S TCM25X50S TCM40X250S TCM80X60S TCM100X80S
TCM12X25S TCM25X75S TCM50X25S TCM80X70S TCM100X90S
TCM12X50S TCM25X100S TCM50X50S TCM80X75S TCM100X100S
TCM12X75S TCM25X150S TCM50X75S TCM80X80S TCM100X125S
TCM12X100S TCM25X200S TCM50X100S TCM80X90S TCM100X150S
TCM12X150S TCM25X250S TCM50X150S TCM80X100S TCM100X175S
TCM16X25S TCM32X25S TCM50X200S TCM80X125S TCM100X200S
TCM16X50S TCM32X50S TCM50X250S TCM80X150S TCM100X225S
TCM16X75S TCM32X75S TCM63X25S TCM80X175S TCM100X250S

Contact us
Add:Shangmei Times, 57 Longguan East Road, Tsinghua Community, Longhua Street, Longhua District, Shenzhen, China

CopyRight © 2010~2017 Shenzhen Fitsi Technology Co.,LTD All Right Reserved.     Sitemap    粤ICP备14001694号-由万创科技提供技术支持