Product Name：2KL Series Internally Piloted and Normally Opened Valve
Product Model：2KL150-15 2KL200-20 2KL250-25 2KL320-32 2KL400-40 2KL500-50
Brand：AirTAC

Type/Item:	Port Size:	Orifice Size(Φmm):	Cv	Valid Area or Section(mm²)	Weight（g）:	Max Operating Pressure Differentia:		Proof Pressure:
						MPa	psi	MPa	psi
2KL150-15	PT1/2	15.0	5.50	100.0	675	Max:0.7 Min:0.05	Max:100 Min:10	1.5	220
2KL200-20	PT3/4	20.0	9.50	170.0	880
2KL250-25	PT1	25.0	12.50	220.0	1125
2KL320-32	PT1 1/4	35.0	23.00	420.0	2710
2KL400-40	PT1 1/2	40.0	31.00	560.0	3260
2KL500-50	PT2	50.0	49.00	880.0	4310

① PT thread, NPT thread and G thread are available.
②The weight in the table is the terminal valve's weight, 2KL150~250 series gormmet valve's weight is 10g less than terminal's. 2KL320~500 series gormmet valve's weight is 20g less than terminal's.

Specification of coil:

Valve Type:	Coil Type:	Power Type:	Frequency(Hz)	Voltage Range	Eletrical Entry	Power Consumption（VA/W）	Insulation	Temperature Rise(℃)
2KL150 2KL200 2KL250	CDA116 CLA116	AC	50	±15%	Terminal(CAD) Gormmet(CLA)	15.0VA	Class H	50
			60			11.0VA		40
		DC	-	±10%		6.5W		30
2KL320 2KL400 2KL500	CDA170 CLA170	AC	50	±15%		35.0VA		65
			60			30.0VA		60
		DC	-	±10%		10.5W		40

Valve's Specification:

Acting:	Internally Piloted
Initial Stats:	Normally Opened
Adaptable Fluid:	Steam, Hight Temperature Water, Oil
Viscosity Limit:	Under 20CST
Ambient and Fluid Temperature(℃):		Water	Steam	Oil	Ambient
	Max	150	183	150	100
	Min	1	-	-10	-20

1.Indirect acting(Internal pilot) and normally closed type 2/2 way solenoid valve. Its can change direction quickly and has large flow.

2.It is compact, small and light weight. It is easy to install and dismantle;

3.The valve body is made of brass . The coil has a Heat resistance classification of Class B. The standard seal material is FPM-F. Please contact us if other material are required.

4.The protection class of the coil is IP65 and there is a choice for grommet or terminal electrical entry.

Installation & Usage:

1. Before installing be sure the valve hasnt been damaged via transportation.

2. The coil must be pure vertical, the inlet and outlet on body must be horizontal it's suggested to use the medium lubricated by 40um filter element Be aware of the flow direction and port size.

3. Please notice whether the installation condition accords with technical requirements(such as'voltage', ' actuation frequency,, working pressure and "scope of application temperature), then the equipment can be installed and used.

4. Take measure to avoid vibration and frozen.

5. Before using the fittings and tubes make sure they are clean. When connecting tofittings

be sure the PTFE Thread Seal Tape is used correctly.

6. To keep the dust away, Default paragraph font Never forget to install dirt-proof boot in air

intake and outlet during dismounting.