Products
Multi-mount Cylinder、Twin-rod Cylinder、Tri-rod Cylinder
AirTAC TR Series Guide Rod Pneumatic Cylinder TR6X10S TR6X20S TR6X30S TR6X40S TR6X50S Dual Shaft Cylinder
  • 1-6
  • 3-6
  • 2-6
  • 4-6
  • 5-6
AirTAC TR Series Guide Rod Pneumatic Cylinder TR6X10S TR6X20S TR6X30S TR6X40S TR6X50S Dual Shaft Cylinder

Product Name: TR Series Dual Shaft Cylinder
Product Model: TR6X10S TR6X20S TR6X30S TR6X40S TR6X50S
Valve Type: Dual Shaft Cylinder, Cyclinder
Brand: AirTAC
Fluid: Air
Acting Type: Double Acting



Download:
Specification:

Specification:

Bore size: 6 10 16 20 25 32
Acting type: Double Acting
Fluid:
Air(to be filtered by 40μm filter element)
Operating Pressure: 0.1~1.0MPa(15~145psi)
Proof pressure: 1.5MPa(215psi)
Temperature(℃): -20~70
Speed rang (mm/s): 30~500 
Adjustable Stroke(mm):
-5~0
Stroke tolerance: (0~+1.0) 
Cushion Type: Burmper
Non-rotating Tolerance: ±0.2° ±0.15° ±0.1°
Port Size: M5X0.8
PT1/8

①Non-rotary accuracy of the cylinder fully retracted state, the cylinder fixed plate can be rotated angle;
②PT thread, NPT thread and G thread are available.


Stroke:

Bore size(mm) Standard Stroke(mm) Max Stroke(mm)
6 10 20 30 40 50 50
10

10 20 30 40 50 60 70 80 90 100 100
16 10 20 30 40 50 60 70 80 90 100 125 150 175 200 200
20 10 20 30 40 50 60 70 80 90 100 125 150 175 200 200
25 10 20 30 40 50 60 70 80 90 100 125 150 175 200 200
32 10 20 30 40 50 60 70 80 90 100 125 150 175 200 200

The 100mm range of non-standard travel range of more than a standard stroke restructuring, its dimensions for the previous standard stroke cylinder dimensions. Such as the stroke of 28 non-standard stroke cylinder is a standard stroke of 30 standard cylinder restructuring, its dimensions and the same.




Product Feature:

1.JIS standard is implemented.

2.The non-rotating precision is high and deflection of the end of rod is low, which is suitable for precise guide.

3.It adopts lengthening type sliding supporting guide. No additional lubricant is needed and it has good performance of guide.

4.Mounting holes on three sides facilitates multi-position mounting.

5.It is good resistance to bending and twisting moments.

6.Except for the axial, each side of the cylinder has installation orifices to provide several installation and fixation ways for the customers.

7.There are two groups of air intake and outlet at two sides of the cylinder for the actual ion.

8.Bumper  in front of the barrel can adjust the stroke of cylinder and relieve impact.

9.Standard configuration of this series has magnet and the type without magnet is not available.


Installation & Usage:

1.When load changes in the work, the cylinder with abundant output capacity shall be ed.

2.Relative cylinder with high temperature resistance or corrosion resistance shall be chosen under the condition of high temperature or corrosion.

3.Necessary protection measure shall be taken in the environment with higher humidity, much dust or water drops, oil dust and welding dregs.

4.Dirty substances in the pipe must be eliminated before cylinder is connected with pipeline to prevent the entrance of particles into the cylinder.

5.The medium used by cylinder shall be filtered to 40μm or below.

6.Anti-freezing measure shall be adopted under low temperature environment to prevent moisture freezing.

7.The cylinder shall be carried out test run without load before application. Prior to run, buffer shall be turned to the minimum and gradually released to avoid the damage on cylinder caused by excessive impact.

8.The cylinder shall avoid the influence of side load in operation to maintain the normal work of cylinder and extend the service life.

9.If the cylinder is dismantled and stored for a long time, please conduct anti-rust treatment to the  surface. Anti-dust caps shall be added in air inlet and outlet ports.

Order Code:
TR Series.jpg
Symbol:
TR Seres.gif
Contact us
E-mail:info@fitsitech.com
Tel:+86-19928764188 
Add:Shangmei Times, 57 Longguan East Road, Tsinghua Community, Longhua Street, Longhua District, Shenzhen, China

     
Inquiry
Name:
E-mail:
Description:
CopyRight © 2010~2017 Shenzhen Fitsi Technology Co.,LTD All Right Reserved.     Sitemap    粤ICP备14001694号-由万创科技提供技术支持